November 2021

14 articles

  • How to replace the jaws on a metalworking vise

    The vise jaws on most metalworking vises (sometimes spelled vices) is made of hardened serrated steel. This increases it’s durability and allows it to handle most metals with ease. Despite this, vise jaws wear out over time, especially if y…

  • How to mount a metalworking vise

    Table of Contents Toggle Selecting your shop table Position of vise on shop table Drill Bolt Holes Mounting a Portable Vise Selecting your shop table The first step to mounting a metalworking vise (sometimes spelled vice) is to pick the rig…

  • How to use a table vise

    It’s very simple to use a table vise (sometimes spelled vice). I will go through the steps below: Table of Contents Toggle Clamp the vise to the Table Open Vise Jaws Close Vise Jaws Ball Joint Vises Clamp the vise to the Table Most models o…

  • What table vice sizes are available?

    Compared to an engineer’s vise, a table vise (sometimes spelled vice) tends to be smaller. but how much smaller? It can vary quite a lot! I will try and go over the different table vise sizes in this article. Table of Contents Toggle Weight…

  • What are the different types of table vise?

    As with all articles of this type, I must start by stressing that vise names do not have enforced standards. Retailers and resellers will slap whatever name they want on a vise; usually this is a name that they think will sell well. There i…

  • What is a table vise?

    Before I begin, I should stress that I’m not aware of any standards when it comes to vise (sometimes spelled vice) names. Manufacturers build the vise to spec, and then retailers and resellers give a name to the vise that they think will se…

  • How to reverse the jaws on a reversible vise

    A reversible vise (sometimes spelled vice) is a great way to increase the jaw opening length at the expense of vise throat depth (most reversible vise models have a little anvil that gets in the way when the vise is reversed). Using the rev…

  • How to rotate the jaws on a rotating vise

    A rotating jaw vise is a vise with multiple jaw types that can be rotated around the x axis. This usually means the vise has a pipe jaw, and a more traditional vise jaw. Rotating the jaws is usually pretty simple. Some vises, like my yost75…

  • How to use a multi-purpose vise

    It’s pretty easy to use a multi-purpose vise (sometimes spelled vice). I will walk you through how to use one in the paragraphs below: Table of Contents Toggle Mounting your vise Open Vise Jaws Place Vise Jaw Pads (If Needed) Clamp Your Vis…

  • What multi-purpose vise sizes are available?

    I will begin to answer this question by asking a clarifying question: the size of what? A multi-purpose vise has a number of different dimensions . These include: Vise jaw width Vise total weight Vise throat depth vise handle length vise ja…

  • What are the different types of multi-purpose vise?

    Before we begin, I should start by saying the “multi-purpose” is not some strict standard. It’s just an advertising label some manufacturers stick on vises that have an extra set of jaws or features. With that in mind, I will go over some o…

  • What is a Multi-Purpose vise?

    A multi-purpose vise (sometimes spelled vice), is a vise with additional functionality over a traditional vise. The most common multi-purpose vise is a vise that has both a set of parallel block jaws, and pipe jaws. The most popular models …

  • What Is A Cross Slide Vise?

    A cross slide vise is a vise with a three lead screws. One lead screw is used to open and close the vise jaws. The second lead screw moves both vise jaws along the x axis (left to right). Third lead screw moves both vise jaws along the y ax…

  • How to use an engineer’s vise

    It’s pretty easy to use an engineer’s vise (sometimes spelled vice). I’ll go through how to use in the paragraphs below: Table of Contents Toggle Mounting your vise Open Vise Jaws Place Vise Jaw Covers (If Needed) Clamp Your Vise Jaws Mount…